Edgers

Our board edger shift assemblies are made to be easily configured for many machine setups, and for ease of installation. Designed to function in sawmill environment day in and day in a out for decades with little to no need for service. They use the same delrin ® bearings that are common to all of our sliding products, that require little to no maintenance. If anything an occasional quick wipe down of the linear shafts with solvent to loosen pitch and sawdust, and you are done! They come with everything needed to get you up and running quickly and can be ordered in custom lengths, the standard being 48″. The units work very well even in the harshest of environments and can handle the stresses produced by vertical edgers.
Applications include: board edgers, vertical and horizontal and any other application that requires linear positioning of a laser for alignment.

sa-002

SA-001 Unison Shift Assembly

The SA-001 unison shift assembly is what is often referred to as “equidistant”. When one saw moves, the opposite saw moves with it, either apart, or together.

Mounting Bolts Spacing:
End plates, 2 ea 5/16″ thru-bolts, 2.750″ spacing
End plate hole distance, same as ordered shaft length

Lengths Available:
24″ up to 72″
Standard length 48″ unless otherwise requested
Lengths over 48″ will incur additional per foot charges

Included Installation Parts:
4 pcs Swivel block (routing) pullies
4- 5/16 x 1.5″ mounting bolts with washers and nuts
2 pcs cable clamps 1/8″ ac
50′ ac cable

* You can also add an SA-009 stationary bracket to allow for a stationary saw. Unison Shift Assembly

SA-002 Independent Shift Assembly

The SA-002 independent shift assembly is just that, configured for independent saws. Both saws can be moved seperately.

Mounting Bolts Spacing:
End plates, 2 ea 5/16″ thru-bolts, 2.750″ spacing
End plate hole distance, same as ordered shaft length

Lengths Available:
24″ up to 72″
Standard length 48″ unless otherwise requested
Lengths over 48″ will incur additional per foot charges

Included Installation Parts:
6 pcs Swivel block (routing) pullies
4- 5/16 x 1.5″ mounting bolts with washers and nuts
4 pcs cable clamps 1/8″ ac
2 pcs 50′ ac cable

* You can also add an SA-009 stationary bracket to allow for a stationary saw. Independent Shift Assembly

sa-002
sa-002

SA-003 Three Rail Sets

The SA-002 independent shift assembly is just that, configured for independent saws. Both saws can be moved seperately.

Mounting Bolts Spacing:
End plates, 2 ea 5/16″ thru-bolts, 2.750″ spacing
End plate hole distance, same as ordered shaft length

Lengths Available:
24″ up to 72″
Standard length 48″ unless otherwise requested
Lengths over 48″ will incur additional per foot charges

Included Installation Parts:
6 pcs Swivel block (routing) pullies
4- 5/16 x 1.5″ mounting bolts with washers and nuts
4 pcs cable clamps 1/8″ ac
2 pcs 50′ ac cable

* You can also add an SA-009 stationary bracket to allow for a stationary saw. Independent Shift Assembly

Frequently Asked Questions

I have 3 moving blades, do you have an assembly for that?

Due to overall complexity and cable routing density issues, we don’t have a 3 saw moving assembly per se. In such a situation, we suggest ordering one standard two saw assembly (SA-001 or SA-002), then adding another assembly configured for one moving unit. Please call if you have questions!

What if my bearings wear out?

Replacement bearing sets can be purchased. Give us a call!

I need more routing pullies!

No problem, we sell these separately as we know not all installations are the same and routing may require more than the standard number.

Request A Quote